View B141XG08-V1_7863058.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 1/22 version: 8 total pages: 20 date: 2003/11/20 product functional specification 14.1 inch xga color tft lcd module model name: b141xg08 v.1 ( ) preliminary specification ( u ) final specification note: this specification is subject to change without notice. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 2/22 contents 1.0 handling precautions......................................................................................................................4 2.0 general description..........................................................................................................................5 2.1 display characteristics..............................................................................................................................................5 2.2 functional block diagram.........................................................................................................................................6 3.0 absolute maximum ratings.............................................................................................................7 4.0 optical characteristics.....................................................................................................................8 5.0 signal interface...............................................................................................................................11 5.1 connectors..............................................................................................................................................................11 5.2 signal pin...............................................................................................................................................................11 5.3 signal description...................................................................................................................................................11 5.4 signal electrical characteristics..............................................................................................................................12 5.5 signal for lamp connector......................................................................................................................................13 6.0 pixel format image.........................................................................................................................14 7.0 parameter guide line for ccfl inverter........................................................................................14 8.0 interface timings............................................................................................................................15 8.1 timing characteristics............................................................................................................................................15 8.2 timing definition...................................................................................................................................................16 9.0 power consumption........................................................................................................................17 10. power on/off sequence...............................................................................................................18 11.0 reliability /safety requirement....................................................................................................19 11.1 reliability test conditions....................................................................................................................................19 11.2 safety....................................................................................................................................................................19 12.0 packing dimension......................................................................................................................20 13.0 mechanical characteristics..........................................................................................................21 13.1 lcm outline dimension (front view)...................................................................................................................21 13.2 lcm outline dimension (rear view)...................................................................................................................22 13.3 screw hole depth and center position..................................................................................................................22 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 3/22 ii record of revision version and date page old description new description remark v1. 2002/12/25 all first release na v2. 2003/1/20 7 ccfl ignition voltage: 1400 vrms ccfl ignition voltage: 1160(25 o c) vrms update 7 operating humidity min : 8 [%rh] operating humidity min : 5 [%rh] update 8 contrast ratio 250 min., 300 typ. contrast ratio 300 min., 350 typ. update 13 dp-1 modify dp-1 column dp: design point 17 vibration test: sine wave.2.16g vibration test: sinusoidal vibration, 1.5g update 18 packing dimension update packing drawing update 19 mechanical characteristics add lcm outline dimension (rear view) and screw hole depth and center position drawing add v3. 2003/2/19 5 typical power consumption 5.0w typical power consumption 5.3w update v4. 2003/2/26 5 weight 400g typ. weight 420g max. update v5. 2003/3/3 5 contrast ratio 350 typ. 300 min contrast ratio 300:1 typ. 250 min update 8 uniformity 13 point 1.6 uniformity 13 point 1.5 update 17 maximum side mount torque 2.0 kgf.cm maximum side mount torque 2.5 kgf.cm update 19 lamp wire length 60 +/-5 mm lamp wire length 100+/-5 mm update 19 screw position: 2.8 +/- 0.2 mm screw position: 2.8 +/- 0.3 mm update 20 cn1 position and screw maximum length :2.3 (typ) cn1 position and screw maximum length : 2.3(max) update 20 screw hole center location from front surface 2.8 0.2mm screw hole center location from front surface 2.8 0.3mm update v6. 2003/4/10 1 b141xg08 b141xg08 v.1 update v7. 2003/8/11 8 response time rising: 15ms falling: 10ms response time rising: 10ms falling: 15ms update v8 2003/11/20 final version www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 4/22 1.0 handling precautions 1) do not press or scratch the surface harder than a hb pencil lead because the polarizers are very fragile and could be easily damaged. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water droplets or oil immediately. long contact with the droplets may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) protect the module from static electricity and insure proper grounding when handling. static electricity may cause damage to the cmos gate array ic. 7) do not disassemble the module. 8) do not press the reflector sheet at the back of the module. 9) avoid damaging the tft module. do not press the center of the ccfl reflector when it was taken out from the packing container. instead, press at the edge of the ccfl reflector softly. 10) do not rotate or tilt the signal interface connector of the tft module when you insert or remove other connector into the signal interface connector. 11) do not twist or bend the tft module when installation of the tft module into an enclosure (notebook pc bezel, for example). it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside when designing the enclosure. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local regulations for disposal. 13) the lcd module contains a small amount of material that has no flammability grade, so it should be supplied by power complied with requirements of limited power source (2.11, iec60950 or ul1950). 14) the ccfl in the lcd module is supplied with limited current circuit (2.4, iec60950 or ul1950). do not connect the ccfl in hazardous voltage circuit. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 5/22 2.0 general description this specification applies to the 14.1 inch color tft/lcd module b141xg08 v1 this module is designed for a display unit of notebook style personal computer. the screen format is intended to support the xga (1024(h) x 768(v)) screen and 262k colors (rgb 6-bits data driver). all input signals are lvds interface compatible. this module does not contain an inverter card for backlight. 2 2 . . 1 1 d d i i s s p p l l a a y y c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s the following items are characteristics summary on the table under 25 condition: items unit specifications screen diagonal [mm] 357(14.1") active area [mm] 285.7(h) x 214.3(v) pixels h x v 1024(x3) x 768 pixel pitch [mm] 0.279(per one triad) x 0.279 pixel arrangement r.g.b. vertical stripe display mode normally white typical white luminance(ccfl=6.0ma) [cd/m 2 ] 200 typ.(5 points average) contrast ratio 250 : 1 min ,300:1 typ responsetime [msec] 25 typ. nominal input voltage vdd [volt] +3.3 typ. typical power consumption (vdd line + vcfl line) [watt] 5.3 watt (w/o inverter, all black pattern)@lcm circuit 1.4 watt(typ.),b/l input 3.9 watt(typ.) weight [grams] 420g max. (w/o inverter) physical size [mm] 299(w) x 228(h) x 5.5(d) max. electrical interface r/g/b data, 3 sync, signals, clock (4 pairs lvds) support color native 262k colors ( rgb 6-bit data driver ) temperature range operating storage (shipping) [ o c] [ o c] 0 to +50 -20 to +60 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 6/22 2 2 . . 2 2 f f u u n n c c t t i i o o n n a a l l b b l l o o c c k k d d i i a a g g r r a a m m the following diagram shows the functional block of the 14.1 inches color tft/lcd module: tft array/cell vdd lcd controller lcd drive card backlight unit 1024(r/g/b) x 3 gnd dc-dc converter ref circuit y-driver x-driver rxin0 rxin1 rxin2 rxclkin (4 pairs lvds) jae fi-xb30s-hf10 mating contactfi-xc3-1-15000 mating housing jae fi-x30h jst bhsr-02vs- 1 mating type sm02b-bhss-1- tb lamp connector(2pin) www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 7/22 3.0 absolute maximum ratings absolute maximum ratings of the module is as following: item symbol min max unit conditions logic/lcd drive voltage vdd -0.3 +4.0 [volt] input voltage of signal vin -0.3 vdd+0.3 [volt] ccfl current icfl - 7 [ma] rms ccfl ignition voltage vs - 1160(25 o c) vrms note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 5 95 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 5 95 [%rh] note 2 vibration 2.16 10-500 [g hz] shock 240 , 2 [g ms] half sine wave note 1 : duration = 50msec note 2 : maximum wet-bulb should be 39 and no condensation. wet bulb temperature chart twb=39 c operating range storage range www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 8/22 4.0 optical characteristics the optical characteristics are measured under stable conditions as follows under 25 condition: item unit conditions min. typ. max. note viewing angle [degree] [degree] horizontal (right) cr = 10 (left) 40 40 - - - - [degree] [degree] vertical (upper) cr = 10 (lower) 10 30 - - - - 3,7 uniformity 5 points 1.2 uniformity 13 points 1.5 2 contrast ratio 250 300 - 6 response time [msec] rising - 10 15 [msec] falling - 15 20 5 color / chromaticity red x 0.57 0.600 0.63 coordinates (cie) red y 0.31 0.340 0.37 green x 0.28 0.310 0.34 green y 0.53 0.560 0.59 blue x 0.12 0.150 0.18 blue y 0.10 0.130 0.16 white x 0.283 0.313 0.343 white y 0.299 0.329 0.359 3,7 white luminance ccfl 6.0ma [cd/m 2 ] 5 points average 170 200 - 1,3,4 note 1: 5 & 13 points position (display area : 285.7mm x 214.3) 1 2 3 4 5 192 384 576 768 512 256 6 7 8 9 10 11 12 13 10mm 10mm 10mm 10mm www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 9/22 note 2: definition of white uniformity: white uniformity is defined as the following with five/thirteen measurements (1~13) at figure in note (1). . note 3: measurement method the lcd module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after lighting backlight for 30 minutes in a stable, windless and dark room. note 4: definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 center of the screen tft-lcd module 50 cm photodetector (bm-5a,bm-7 or equivalent) lcd panel field=2 w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five (1,2,3,4,5) points w5 = minimum brightness of five (1,2,3,4,5) points www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 10/22 l (x) is corresponding to the luminance of the point x at figure in note (1). note 5: definition of response time: the output signals of bm-7 or equivalent are measured when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the response time interval between the 10% and 90% of amplitudes. refer to figure as below. note 6. definition of contrast ratio: contrast ratio is calculated with the following formula. note 7. definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10 % 90 % 100 % contrast ratio (cr)= brightness on the white state brightness on the black state www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 11/22 5.0 signal interface 5 5 . . 1 1 c c o o n n n n e e c c t t o o r r s s physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for signal connector manufacturer jae type / part number fi-xb30s-hf10 mating housing/part number fi-x30h mating contact/part number fi-xc3-1-15000 connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 5 5 . . 2 2 s s i i g g n n a a l l p p i i n n pin# signal name pin# signal name 1 gnd 2 vdd 3 vdd 4 v edid 5 nc 6 clk edid 7 data edid 8 rxin0- 9 rxin0+ 10 gnd 11 rxin1- 12 rxin1+ 13 gnd 14 rxin2- 15 rxin2+ 16 gnd 17 rxclkin- 18 rxclkin+ 19 gnd 20~30 nc 5 5 . . 3 3 s s i i g g n n a a l l d d e e s s c c r r i i p p t t i i o o n n the module uses a lvds receiver embedded in auo s asic. lvds is a differential signal technology for lcd interface and high-speed data transfer device. signal name description v edid +3.3v edid power clk edid edid clock input data edid edid data input rxin0-, rxin0+ lvds differential data input(red0-red5, green0) rxin1-, rxin1+ lvds differential data input(green1-green5, blue0-blue1) rxin2-, rxin2+ lvds differential data input(blue2-blue5, hsync, vsync, dsptmg) rxclkin-, rxclkin0+ lvds differential clock input vdd +3.3v power supply gnd ground note : input signals shall be in low status when vdd is off. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 12/22 internal circuit of lvds inputs are as following. signal name description +red5 +red4 +red3 +red2 +red1 +red0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. +green 5 +green 4 +green 3 +green 2 +green 1 +green 0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. +blue 5 +blue 4 +blue 3 +blue 2 +blue 1 +blue 0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. -dtclk data clock the typical frequency is 65.0 mhz. the signal is used to strobe the pixel data and dsptmg signals. all pixel data shall be valid at the falling edge when the dsptmg signal is high. dsptmg display timing this signal is strobed at the falling edge of -dtclk. when the signal is high, the pixel data shall be valid to be displayed. vsync vertical sync the signal is synchronized to -dtclk . hsync horizontal sync the signal is synchronized to -dtclk . note: output signals from any system shall be low or hi-z state when vdd is off. 5 5 . . 4 4 s s i i g g n n a a l l e e l l e e c c t t r r i i c c a a l l c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s input signals shall be in low status when vdd is off. it is recommended to refer the specifications of sn75lvds86dgg (texas instruments) in detail. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high voltage(vcm=+1.2v) 100 [mv] vtl differential input low voltage(vcm=+1.2v) -100 [mv] www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 13/22 lvds macro ac characteristics are as follows: min. max. clock frequency (f) 50mhz 67mhz data setup time (tsu) 600ps data hold time (thd) 600ps 5 5 . . 5 5 s s i i g g n n a a l l f f o o r r l l a a m m p p c c o o n n n n e e c c t t o o r r pin # signal name 1 lamp high voltage 2 lamp low voltage thd tsu input clock input data t f www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 14/22 6.0 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 01 10221023 1st line 768th line 7.0 parameter guide line for ccfl inverter parameter min dp-1 max units condition white luminance 5 points average 170 200 ? [cd/m 2 ] (ta=25 ) ccfl current(icfl) 6.0 7.0 [ma] rms (ta=25 ) note 2 ccfl frequency(fcfl) 50 60 70 [khz] (ta=25 ) note 3 ccfl ignition voltage(vs) ? 1500 [volt] rms (ta= 0 ) note 4 ccfl voltage (reference) (vcfl) ? 650 ? [volt] rms (ta=25 ) note 5 ccfl power consumption (pcfl) ? 3.9 ? [watt] (ta=25 ) note 5 note 1 : dp-1 are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 15/22 *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit ver carefully. impedance of ccfl, for instance, becomes more than 1 [m ohm] when ccfl is damaged. *4 generally, ccfl has some amount of delay time after applying start-up voltage. it is recommended to keep on applying start-up voltage for 1 [sec] until discharge. *5 the ccfl inverter operating frequency must be carefully chosen so that no interfering noise stripes on the screen were induced. *6 reducing ccfl current increases ccfl discharge voltage and generally increases ccfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2 : it should be employed the inverter, which has duty dimming , if iccfl is less than 4ma. note 3 : the ccfl inverter operating frequency should be carefully determined to avoid interference between inverter and tft lcd. note 4: the inverter open voltage should be designed larger than the lamp starting voltage at t=0 o c, otherwise backlight may be blinking for a moment after turning on or not be able to turn on. the open voltage should be measured after ballast capacitor. if an inverter has shutdown function it should keep its open voltage. for longer than 1 second even if lamp connector is open. note 5 : calculator value for reference (icfl vcfl=pcfl) 8.0 interface timings basically, interface timings should match the vesa 1024x768 /60hz (vg901101) manufacturing guide line timing. 8 8 . . 1 1 t t i i m m i i n n g g c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s symbol description min typ max unit fdck dtclk frequency 65.00 [mhz] tck dtclk cycle time 15.38 [nsec] tx x total time 1206 1344 2047 [tck] tacx x active time 129 1024 [tck] tbkx x blank time 90 320 [tck] hsync h frequency 48.363 [khz] hsw h-sync width 2 136 [tck] hbp h back porch 1 160 [tck] hfp h front porch 0 24 [tck] ty y total time 771 806 1023 [tx] tacy y active time 768 [tx] vsync frame rate (55) 60 61 [hz] vw v-sync width 1 6 [tx] vfp v-sync front porch 1 3 [tx] vbp v-sync back porch 7 29 63 [tx] note: hsw(h-sync width) + hbp(h-sync back porch) should be less than 515 tck. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 16/22 8 8 . . 2 2 t t i i m m i i n n g g d d e e f f i i n n i i t t i i o o n n tx hsw hbp hfp tacx h-sync dsptm 38h vfp vbp vw tacy v-sync dsptmg www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 17/22 9.0 power consumption input power specifications are as follows; symbol parameter min typ max units condition module vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] load capacitance 20uf pdd vdd power 1.4 [watt] all black pattern pdd max vdd power max 1.65 [watt] max pattern note idd idd current 350 ma 64 grayscale pattern idd max idd current max 450 ma vertical stripe line pattern note vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p vddns allowable logic/lcd drive ripple noise 100 [mv] p-p lamp icfl ccfl current 3.0 6.0 7.0 [ma] rms (ta=25 ) vcfl ccfl voltage (reference) ? 650 ? [volt] rms (ta=25 ) pcfl ccfl power consumption ? 3.9 ? [watt] (ta=25 ) total power consumption 5.3 watt (w/o inverter, all black pattern)@lcm circuit 1.4 watt(typ.),b/l input 3.9 watt(typ.) note : vdd=3.3v www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 18/22 10. power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. sequence of power-on/off and signal-on/off power supply vdd lvds interface backlight on apply the lamp voltage within the lcd operating range. when the backlight turns on before the lcd operation or the lcd turns off before the backlight turns off, the display may momentarily become abnormal. 1ms Q t1 Q 10ms 6ms Q t2 Q 50ms 0ms Q t3 50ms 400ms Q t4 200ms Q t5 200ms Q t6 t4 t3 t2 t5 v alid t1 0.1vdd 0.9vdd 0.1vdd 0.9vdd t6 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 19/22 11.0 reliability /safety requirement 1 1 1 1 . . 1 1 r r e e l l i i a a b b i i l l i i t t y y t t e e s s t t c c o o n n d d i i t t i i o o n n s s items required condition temperature humidity bias 40 /90%,300hr high temperature operation 50 /dry,300hr low temperature operation 0 ,500hr continuous life 25 ,2000 hours on/off test on/30 sec. off/30sec., 30,000 cycles hot storage 60 /40% rh ,240 hours cold storage -20 /50% rh ,240 hours thermal shock test -20 /30 min ,60 /30 min 100cycles hot start test 50 /1 hr min. power on/off per 5 minutes, 5 times cold start test 0 /1 hr min. power on/off per 5 minutes, 5 times shock test (non-operating) 240g, 2ms, half-sine wave vibration test (non-operating) sinusoidal vibration, 1.5g zero-to- peak, 10 to 500 hz, 0.5 octave/minute; 0.5hr in each of three mutually perpendicular axes. esd contact : operation 8kv / non-operation 10kv air : operation 15kv / non-operation 20kv altitude test 10000 ft / operation / 8hr 30000ft / non-operation / 24r maximum side mount torque 2.5kgf.cm . ccfl life : 10,000 hours minimum mtbf(excluding the ccfl) : 30,000 hours with a confidence level 90% 1 1 1 1 . . 2 2 s s a a f f e e t t y y ul 60950 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 20/22 12.0 packing dimension carton side cushion for mark 14" use paper pad top cushion position carton label "h" taping close 14.1" panel * 20 pcs 14.1" panel esd bag www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 21/22 13.0 mechanical characteristics 1 1 3 3 . . 1 1 l l c c m m o o u u t t l l i i n n e e d d i i m m e e n n s s i i o o n n ( ( f f r r o o n n t t v v i i e e w w ) ) www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2002 all rights reserved. b141xg08 v.1 no reproduction and redistribution allowed. 22/22 1 1 3 3 . . 2 2 l l c c m m o o u u t t l l i i n n e e d d i i m m e e n n s s i i o o n n ( ( r r e e a a r r v v i i e e w w ) ) b 1 4 1 x g 0 8 5 9 . 1 4 b 1 7 . 0 0 1 - m 1 7 1 1 3 3 . . 3 3 s s c c r r e e w w h h o o l l e e d d e e p p t t h h a a n n d d c c e e n n t t e e r r p p o o s s i i t t i i o o n n screw hole minimum depth, from side surface =2.5 mm (see drawing) screw hole center location, from front surface = 2.8 0.3mm (see drawing) screw maximum length = 2.3 mm (see drawing) screw torque: maximum2.5 kgzf-cm www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of B141XG08-V1

	To Download B141XG08-V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .